nrf2rfm69

Converter module to enable RFM69 ussage on NRF24 nodes in MySensors

• 

  Joost commented 5 years ago
  

  @acb
  Hi @acb and others, regarding "Do you know if there is a version of this board that is pad-compatible with the C-versions of these HopeRF RFM69s before I go searching? (Since I believe the C-versions are also pad-compatible with the RFM95s…)" - did you find any alternative?
  I'm in the same boat looking for an adapter from NRF24 to the footprint of RFM69*C = RFM95/96.
  Thanks, Joost

• 

  acb commented 6 years ago
  

  Yes @tbowmo, I saw the solder pads on the back - although thanks for the reminder (and image @mfalkvidd)!

  I’m not using those (yet) since I didn’t want to “permanently” attach one of my “precious” RFM69HWs to it whilst I’m tinkering with all these lovely new radios you now support. RFM95 next I hope, after checking out the FOTA and signing! You guys have really done great work!

  I also wanted to range-test with a few different externally mounted antennas I had lying around and so I combined pads for a surface mount U.fl and edge SMA on my own NRF2RFM69.

  Not a great deal of room around the SBGW’s pin breakout (P1) for a helical - although I really respect the design choices - so I figure I’ll probably breakout those pins to pigtail an SMA.

  But this is getting a bit off-topic Re: NRF2RFM69 and probably better suited to the Sensebender Gateway thread.

  Bringing it back on-topic a little:

  Do you know if there is a version of this board that is pad-compatible with the C-versions of these HopeRF RFM69s before I go searching? (Since I believe the C-versions are also pad-compatible with the RFM95s…)

• 

  symos commented 6 years ago
  

  @alexsh1 Thanks, though I'm not sure you understood exactly what I'm saying.
  If I connect the radio to the RPi 3 following the NRF instructions and using the NRF2RFM69 adapter, it is NOT working.

  For it to work, I MUST connect the "IRQ" pin of the NRF2RFM69 (which corresponds to RFM's D100 pin) to RPi's pin 22 (which is where CE is supposed to go, according to instructions) and leave CE unconnected.

  So if someone is using the NRF2RFM69 adapter and tries to connect the radio to the RPi 3 as if it were an NRF, it won't work. I think this is confusing and that's why I posted it.

• 

  mfalkvidd commented 6 years ago
  

  Adding image for reference
  

• 

  tbowmo commented 6 years ago
  

  @acb

  You do know that there is solder pads for RFM69HW on the back of the gateway, right? And the board defs for the gateway are configured to use those pins for the RFM69 by default.

• 

  acb commented 6 years ago
  

  On a related note, if anyone is trying to get the NRF2RFM69 board or similar working with the awesome Sensebender Gateway and W5100 Ethernet board, here’s what I had to do today as far as the CS and IRQ defines are concerned.

  [FYI: I’m coming back to MySensors after a long hiatus and am in the process of updating (some from v1.3!) all my gateways and sensors...]

  Aside from the usual radio selection, I had use the new driver and point the RFM69 NSS and IRQ pins at the nRF CS and IRQ nets. Also, if you want to, you can point the RFM69 RESET pin at the nRF CE net:

  #define MY_RFM69_NEW_DRIVER
  #define MY_RF69_RESET 34  // Note: Should be MY_RFM69_RST_PIN, but this didn’t work.
  #define MY_RFM69_IRQ_PIN 31
  #define MY_RFM69_IRQ_NUM digitalPinToInterrupt(MY_RFM69_IRQ_PIN)
  #define MY_RFM69_CS_PIN 29
  #define MY_DEBUG_VERBOSE_RFM69  // Note: Only if you want to check the pins, RSSI, etc.
  

  

  Hope that helps someone.

• 

  alexsh1 commented 6 years ago
  

  @tbowmo I wonder what would be an example of using it?!
  I knew it would be supported at a certain time in the future but I did not realise it it supported already.

• 

  mfalkvidd commented 6 years ago
  

  see the #MY_RF24_IRQ_PIN define, which is used around here

  Or the documentation at https://www.mysensors.org/apidocs/group__RF24SettingGrpPub.html#ga23c9926f77307bf1b0263432232e4f4a

• 

  tbowmo commented 6 years ago
  

  @alexsh1

  You can enable interrupt usage for NRF24, depending on your hardware and needs.

  see the #MY_RF24_IRQ_PIN define, which is used around here